更多"根据所显示的配置信息,由inside域发往Internet的IP分组,"的相关试题:
[填空题]show命令可以帮助获得监控路由器的重要信息,使用show命令可以了解路由器的配置、接口的工作状态、( )、各种协议的工作状况、( )等对故障排除非常有用的信息。
[简答题]下面是某路由器的部分配置信息,解释(n)处标有下划线部分的含义。 【配置路由器信息】 Current configuration: ! version 11.3 no service password-encryption ! hostname router1 第(1)处 ! enable password nwd12345 第(2)处 ! interface Ethernet0 ip address 192.4.1.1.255.255.255.0 1 interface Serla10 ip address 192.3.1.1.255.255.255.0 encapsulation frame-relay IETF 第(3)处 no ip mroute-cache bandwidth 2000 第(4)处 frame-relaymanin 192.3.1.2100 broadcast 第(5)处 frame-relaylmi-typecisco ! router ospf1 第(6)处 network 192.1.1.0.0.0.0.255 area0 第(7)处 network 192.3.1.0.0.0.0.255 area0 network 192.4.1.0.0.0.0.255 area0 neighbor 192.1.1.2 第(8)处 ! End
[填空题]下面是某路由器的部分配置信息,解释(n)处标有下划线部分的含义。
[配置路由器信息]
Current configuration:
!
Version11.3
No service password-encryption
!
Hostname router1 (6)
!
Enable password nwd12345 (7)
!
Interface Ethernet 0
Ip address 192.4.1.1 255.255.255.0
!
Interface serial 0
Ip address 192.3.1.1 255.255.255.0
Encansulation frame-relay IETF
No ip mroute-cache
Bandwidth 2000
Frame-relay map ip 192.3.1.2 100 broadcast
Frame-relay lmi-type cisco
!
Router ospf1 (8)
Network 192.1.1.0 0.0.0.255 area0 (9)
Network 192.1.3.0 0.0.0.255 area0
Network 192.1.4.0 0.0.0.255 area0
Neighbor 192.1.1.2 (10)
[填空题]查看路由器的配置信息和路由表,分别使用show configuration和( )命令。
[填空题]某企业采用DDN专线通过一台Cisco路由接入Internet。请阅读以下路由器的配置信息,并补充横线处的配置命令(参数)或注释,按注释要求完成路由器的配置。
Router>en 进入特权模式
Router # config terminal 进入全局模式
Router(config) # ______ 设置特权口令为Cisco
Router(config) # line vty 0 4
Router(config-line) # password abcl23 ______
Router(config-line) # exit
Router(config) # interface eth0/0 进入以太网接口配置模式
Router(config-if) # ip address 202.117.1.1 255.255.255.0
设置IP地址和掩码
Router(config-if) # no shutdown
Router(config-if) # exti
Router(config) # ______ serial0/0 进入串口S0/0配置模式
Ronter(config-if) # ip address 211.175.132.10 255.255.255.252设置IP地址和掩码
Router(config-if) # ______ 指定带宽为1Mbps
RoUter(config-if) # ______ 封装PPP协议
Router(config-if) # no edp enable
Router(config-if) # no shutdown
Router(config-if) # end
Router>