更多"[单选题]An LTM Specialist configures a"的相关试题:
[单选题]An LTM Specialist configures a new virtual server with a single pool member. The LTM Specialist has NOT defined a health monitor for the pool, pool member or node.
What is the status of the virtual server?
A. Available (Enabled)
B. Offline (Disabled)
C. Unavailable (Enabled)
D. Unknown (Enabled)
[单选题]An LTM Specialist needs to configures virtual server that uses PVA or OPVA Which virtual server type should be used?
A. Stateless
B. Performance (HTTP)
C. Standard
D. Performance (Layer 4)
[单选题]AN LTM Specialist is setting up a new HTTPS virtual server to decrypt client traffic. SNAT the traffic and send the encrypted traffic to the poor member, the client's IP address must be included in the traffic sent to the pool member.
What is a complete set of profiles that must be configured for the virtual server to meet these requirements?
A. TCP, Client SSL, Server SSL
B. TCP , Server SSL, HTTP
C. TCP, Client SSL, HTTP
D. TCP, Client SSL, Server SSL, HTTP
[单选题]An LTM Specialist is configuring a new virtual server on an LTM device and assigning a SNAT pool that is already is use another virtual server. Both virtual servers use the same pool members to load balance traffic. A maximum of 35,000 users needs to be able to access each virtual server ta any time. The network architecture does NOT allow the backend servers to use the LTM device as a default gateway.
What is the minimum number of SNAT addresses required in the SNAT pool to meet the needs of the virtual servers?
A. 2
B. 3
C. 4
D. 1
Explanation:
Both vs share the same snat pool, and both use the same pool member. Then the concurrent number of snatpool will be added. For each VS, there is a maximum of 35,000 users, and those two VSs have a
Maximum of 70,000 users. The stem did not mention how many connections each user would have concurrently. Calculated with a minimum of 1 connection, then 70,000 connections would be concurrent. One IP can support 65,535 connection. Therefore, at least 2 or more snaptips are required
[单选题]An LTM specialist needs to create a new account with the admin role called "newadmin' and access to all partitions.
Which tmsh command should be executed?
A. create /auth user newadmin partition-access add {all-partitions {role admin }} prompt for-password.
B. create /users newadmin partition-access add {all-partitions {role admin JJ prompt for-password.
C. create /user newadmin partition-access add (all-partitions {role admin }} prompt- for-password.
D. create / sys user newadmin partition-access add (all-partitions {role admin )} prompt-for-password.
Explanation:
Examining the use of commands, the creation of user is subordinate to auth
[多选题]An LTM Specialist must create a new virtual server for HTTP access. The LTM Specialist creates a forwarding virtual server to reach the resource.
What is a potential result of this action?
A. IP conflict result
B. HTTP traffic is NOT allowed
C. Other service ports could be allowed
D. Packet filter allowances are also required
[单选题]A new HITP server has been deployed on an LTM device. The application running on the server must be monitored by the LIM device. The following is required:
A new HITP server has been deployed on an LTM device. The application running on the server must be monitored by the LIM device. The following is required:
When the server is unavailable, it will send an HTTP status code of 200 in response to a request for the status html page.
When the server is available. I will send and HTTP status code of 201 in response to a request for the status html page.
When the 200 status code is received, the pool member should receive No new connections. Which configuration change should be made to meet these requirements?
A. set the Send String to GET/ status html and the Receive String to 200 and Receive Disable String to 201.
B. set the Send String to GET Arian and the Receive String to 200 and Receive Disable String to 201.
C. set the Send String to GET Arian and the Receive Disable String to 200 and Receive String to 201.
D. set the Send String to Get /status html and the Receive Disable String to 200 and Receive String to 201.
[多选题]A new iRule needs to be tested. The LTM Specialist needs to measure page load times and monitor potential changes in memory usage A load test is scheduled.
Which two features should the LTM Specialist use to monitor these requirements? (Choose two.)
A. Tmsh show memory
B. Analytics
C. Tmsh show sys proc-info
D. Tmsh show sys provision
Explanation:
Need to detect memory changes in real time, use to Page load times with Analytics profile
[单选题]Exhibit.
The LTM devices LTM1 and LTM2 are configured in a Device Group (Sync Failover) with Network Failover configured on both the management and HA and Internal VLANS. and ConfigSync is confined in a Device Group (Sync Failover) with Network Failover and internal are tagged on a single trunk with subnets Connection Mirroring is configured on both the HA interlace directly connected between LTM1 and LTM2, and the management interlace is connected to a management switch. The LTM devices have four Traffic Groups defined, and both LTM devices are healthy and capable of passing traffic for any of the Traffic Groups.
An LTM Specialist disconnects the cable for the HA network in an effort to test failover. Which HA functionality works in this case?
A. ConfigSync does NOT work. Connection Mirroring floes NOT work.
B. ConfigSync works Connection Mirroring works
C. ConfigSync works. Connection Mirroring docs NOT work
D. ConfigSync does NOT work; Connection Mirroring works
[单选题]Refer to the exhibit.
The LTM devices LTM3 and LTM2 have four Traffic Groups defined with approximately the sar of failover objects defined in each group.
- Traffic Groups A and C have Default Device set to LTM1
- Traffic Groups Band D have Default Device set to LTM2.
- Traffic Groups B and C do NOT have Auto Failback enabled. Traffic Groups A and D have Auto Failback
Enabled with a timeout value of 60 seconds.
- Traffic Groups A and D have Auto Fallback enabled with a timeout value of 60 seconds. Both LTM devices are healthy and able to pass traffic for any Traffic Group.
LTM1 loses connectivity on interface 1.4. The LTM Specialists notified 60 seconds after the interface goes down.
What is the state of the Traffic Groups on each LTM device?
A.LTM1: Traffic Group CLTM2: Traffic Groups
A,
B, and 0
B.LTM1: No Traffic GroupsLTM2: Traffic Groups
A,B.
C, and DC.
[单选题]One LTM device in an HA pair of LTM devices is unable to reach its default gateway. An HA Failover event needs to happen.
Which configuration item enables this behavior?
A. iRule
B. Gateway Fail Safe
C. Gateway pool monitor
D. Gateway pool
[单选题]An LTM Specialist regularly provides analytics reports that show that traffic generated by different subnets within the organization. The LTM Specialist needs show the associate department names next the IP addresses in the reports.
Which step should the LTM Specialist take to meet this requirement?
A. use an iRule to change the output of the report
B. export the report and add the department names manually
C. create VLANs for each subnet and set the name accordingly
D. define active subnets and assign a name to certain subnets
[单选题]An LTM Specialist observes decreased performance and intermittent connection reap LTM system.
Based on the configuration, which action will address these issues?
A. Use an optimized TCP profile.
B. Use a FastL4 profile on the virtual server
C. Use a default caching profile on the virtual server.
D. Use a shorter idle timeout on the TCP profile.
[单选题]An LTM Specialist needs to provide statistics regarding the round-trip time between the clients and the servers.
Which metric should be part of the analytics profile to provide that information?
A. Page Load Time
B. User Sessions
C. Max TPS and Throughout
D. Response Codes
[单选题]An LTM Specialist plans to enable connection mirroring for a virtual server in an HA environment. What must the LTM Specialist consider before implementing the configuration change?
A. Impact on system performance that might be noticeable
B. The add-on license that is required for this feature to be available
C. Creating the required separate interface for connection mirroring
D. Decreased number of possible concurrent connections to that virtual server
Explanation:
Connection mirroring will bring performance consumption
[单选题]Two LTM devices must be manually configured to restrict in the same Device Group. What is the correct order of steps to meet this requirement?
A. Configure VLAN, Configure-Sync IP, Configure Failover type, Establish Device Trust, Sync Device Trust, Create type, Establish Device Sync Device Trust, Create Device Group.
B. Configure VLAN, Configure Self-IPs, Configure Config-Sync IP. Configure Failover type, Establish Device Trust, Sync Device Trust, Create Device Group.
C. Configure Self-IPs, Configure VLAN, Configure Config-Sync IP. Configure Failover type, Establish Device Trust, Sync Device Trust, Create Device Group
D. Configure VLAN, Configure Config-Sync IP. Configure Self-IPs. Configure Failover type. Establish Device Trust, Create Device Group
[单选题]AN LTM Specialist is using an external monitor evaluate the hard drive usage of a node. The monitor has marked the node down because it exceeded the specific threshold. The disk usage on the server has
Been corrected below the threshold, however, the node remains offline.
Which feature is causing this problem?
A. The parameter Time Until UP has a value greater than 0
B. The value of Manual Resume is set to No
C. The value for UP interval is enable with a value greater than 0
D. The value for Manual Resume is set to Yes
[单选题]An LTM device is configure with the wildcard virtual servers displayed below.
A client connection is made to 172.24.31.14:443.
A. VS_172_24_1_WILDCARD
B. VS_HTTP_WILDCARD
C. VS_172_24_WILDCARD
D. VS_HTTPS_WILDCARD
Explanation:
Match the network segment first and then port.
[单选题]An LTM device receives a response string containing "error"
Which monitor type and parameter will mark the HTTP server as down?
A. HTTP monitor, Receive String "error", and set the Reverse option to Yes
B. HTTP monitor and Receive String "error'' ... flag is up
C. HTTP monitor. Receive String "down", and set the Reverse option to Yes .... flag is
D. HTTP monitor and Receive Disable String "error''.... flag is disable
