更多"The sequence of fuel injection into"的相关试题:
[单项选择]Fuel injection systems meter fuel, atomize fuel, and （）.
A. create turbulence in the combustion chamber
B. aid in completing cylinder scavenging
C. inject fuel at the proper time
D. minimize fuel penetration into the cylinder
[单项选择]During the fuel injection period, fuel pressure must exceed cylinder gas pressure to （）.
A. ensure penetration and distribution of the fuel in the combustion chamber
B. ensure the needle valve is flushed clean during each injection
C. prevent combustion gas blowback into the open needle valve
D. prevent reflected pressure waves when the needle valve closes
[单项选择]Air in the fuel lines to the fuel injection nozzles of a diesel will result in （）.
A. lower compression pressures
B. overheating without smoking
C. failure to start
D. a run away without load
[单项选择]Faulty operation of diesel engine fuel injection nozzles can be directly caused by （）.
A. water in the fuel oil supply
B. excessive fuel nozzle holder cooling
C. a distorted fuel spray pattern
D. leakage past the plunger into the oil drain
[单项选择]The main source of fuel injection system malfunctions is （）
A. improper adjustments
B. contaminated fuel
C. coated fuel lines
D. excessive vibration
[单项选择]Problems with the diesel engine fuel injection pump are usually caused by（）
A. improper adjustment
B. contaminated fuel
C. kinked fuel lines
D. excessive engine vibration
[单项选择]Heat damage to fuel injection nozzles on small high-speed diesel engines, can be prevented by（）
A. employing fuel oil as a cooling medium
B. preventing hard carbon deposit on nozzle tips
C. avoiding fuel oil temperature exceeding builder’s specification
D. ensuring good metallic contact between nozzles and cylinder heads
[单项选择]Fuel injection equipment must be kept in good condition, timed correctly, and the （）in each cylinder must also be carefully balanced so that individual cylinders are not overloaded.
A. MIP
B. MCR
C. MEP
D. BHP
[单项选择]The amount of fuel injection into a diesel engine cylinder by a unit injector, is controlled by（）
A. the firing pressure in the cylinder
B. a metering helix inside the pump
C. varying the physical length of the plunger stroke
D. varying the clearance between the injector cam and the injector rocker arm
[单项选择]If keep the fuel injection of main engine unchanged when ship is fouled, that will causeⅠ.The speed of main engine to be reduced Ⅱ.Ship speed to be reduced Ⅲ.The resistance torque of propeller to be increased Ⅳ.Trim at stern to increase（）
A. Ⅰ + Ⅱ
B. Ⅰ ~ Ⅲ
C. Ⅰ ~ Ⅳ
D. Ⅰ + Ⅱ + Ⅳ
[单项选择]A fuel injection valve opening at pressure lower than normal will result in（）.
A. late fuel injection
B. early fuel injection
C. high exhaust temperature from that cylinder
D. decreased effective stroke from that injector
[单项选择]When ship is fouled, increasing the fuel injection for keeping the normal speed will cause the main engine （）
A. to work as overload characteristic
B. overspeed
C. over mechanical load only
D. over thermal load only
[单项选择]Fuel injection valves should be taken out, cleaned, and lifting checked every （）.
A. two to four months
B. four to six months
C. six to eight months
[单项选择]Late fuel injection in a diesel engine is indicated by low firing pressure with （）
A. low exhaust temperature
B. low exhaust pressure
C. mechanical knock in each cylinder
D. black or gray exhaust smoke
[单项选择]If the diesel engine fuel injection timing is changed to delay the start of injection until the pistons are at top dead center, the engine will（）
A. backfire through the air intakes
B. develop less power under load
C. have high firing pressures
D. lift its cylinder relief valves
[单项选择]A diesel engine will lose power if fuel injection occurs too early because the （）
A. fuel will not be properly atomized in the cylinder
B. ignition will be delayed due to low ignition temperature
C. maximum fuel expansion will occur on the compression stroke
D. fuel will ignite before top dead center
