更多"To function properly, oil control r"的相关试题:
[单项选择]Oil control rings used in two-stroke/cycle diesel engines are located near the bottom of the piston skirt in order to ()
A. increase the liner area covered by the oil film
B. maintain an oil film on the lower liner where scuffing is prevalent
C. keep excess oil away from intake and exhaust ports
D. help cushion piston skirt side thrust by providing a hydrodynamic oil wedge
[单项选择]The primary purpose of oil control rings on a diesel piston is to()
A. provide a reservoir for cylinder lubrication
B. pump oil into the combustion space for cylinder cooling
C. prevent excessive lubricating oil consumption
D. allow hydraulic oil film formation on the cylinder
[单项选择]The function of the piston compression rings used in a diesel engine is to ()
A. seal the space between the piston and liner
B. transmit heat from the piston to the cylinder liner
C. reduce the amount of combustion gas blow-by
D. all of the above
[单项选择]Piston compression rings used in a diesel engine function to ()
A. transfer heat from the cylinder to the piston
B. scrape oil from the sides of the piston
C. seal the combustion space from the crankcases
D. prevent any piston contact with the cylinder liner
[单项选择]The purpose of the wearing rings used in a centrifugal pump is to ().
A. prevent an internal explosion in the pump when it is overheated
B. enable a visual inspection of the pump while it is running
C. insure a proper alignment of the pump coupling to the driver
D. accommodate for friction between the impeller and the easing
[单项选择]What is a function of the wearing rings used in most centrifugal pumps?()
A. Absorb erosion of high velocity discharge stream
B. Seal pump shaft against entry of air
C. Isolate the discharge side from the suction side
D. Dampen the turbulent discharge flow
[单项选择]If an emergency pump control is used as the emergency shutdown on a tank vessel,it must().
A. stop the flow of oil at the main deck manifold
B. prevent the oil from leaving the shore facility
C. prevent the oil from siphoning through the pump
D. None of the above
[单项选择]In a commonly used fuel oil system, the oil is stored in tanks in the double bottom from which it is pumped to () and heated.
A. a service tank
B. a settling tank
C. an expansion tank
D. a double bottom tank
[单项选择]The term OIL as used in the Oil Pollution Regulations means().
A. fuel oil
B. sludge
C. oil refuse
D. All of the above
[单项选择]The preferred type of pollution control for oil spills on the water is(are) ().
A. straw
B. booms
C. skimmers
D. chemical dispersants
[单项选择]If a used lube oil analysis indicates excessive fuel dilution, the lube oil should be ()
A. changed
B. centrifuged
C. filtered
D. settled
[单项选择]If a used lube oil analysis indicates an excessive chromate content, this means ()
A. air filtration is inadequate
B. engine coolant leaking into the lube oil
C. fuel oil is leaking into the lube oil
D. the piston rings are excessively worn
[单项选择]If the analysis of used lube oil indicates a high content of iron particles, this could indicate()
A. corrosive deterioration of a bearing
B. inadequate air filtration
C. excessive ring and liner wear
D. excessive cooling of lubricating oil
[单项选择]
The sequence of parts in a generally used fuel oil supply system for a main engine is ()
(1)tanks in the double bottom
(2)centrifuges
(3)service tank
(4)settling tank
(5)viscosity regulator
A. (1)-(2)-(4)-(3)-(5)
B. (1)-(4)-(2)-(3)-(5)
C. (1)-(3)-(2)-(4)-(5)
D. (1)-(5)-(4)-(2)-(3)
[单项选择]The main purpose of the piston oil scraper rings is to ().
A. seal the space between the piston and the liner
B. reduce the amount of lube oil burned in the combustion chamber
C. transmit heat from the piston to the cylinder liner
D. damp out fluctuations of the piston side thrust
[单项选择]The radar control used to reduce sea return at close ranges is the().
A. gain control
B. sensitivity time control
C. fast time constant
D. pulse length control
[单项选择]The film of oil between the rings and the liner is not only essential for the lubrication but also plays an important part in achieving ().
A. an oil seal
B. removing heat
C. a gas seal
D. cooling the piston