更多"Which command sets and automaticall"的相关试题:
[单项选择]Which command sets and automatically encrypts the privileged enable mode password?（）
A. enbale password c1sco
B. secret enable c1sco
C. password enable c1sco
D. enable secret c1sco
[单项选择]Which command encrypts all plaintext passwords?（）
A. Router(config)#password-encryption
B. Router(config)#service password-encryption
C. Router#service password-encryption
D. Router# password-encryption
[单项选择]Which configuration command sets the MPLS interface bandwidth to 15 Mbps?（）
A. set bandwidth 15
B. mpls bandwidth 15
C. set bandwidth 15000
D. mpls bandwidth 15000
[单项选择]Which command sets and automatically encrypts the privileged enable mode password？（）
A. enbale password c1sco
B. secret enable c1sco
C. password enable c1sco
D. enable secret c1sco
[多项选择]After executing the "show host" command, which of the information below would you see?（）
A. The IP addresses of workstations allowed gain access to the router via an access list
B. Permanent name-to-address mappings created using the ip host command.
C. Temporary and permanent DNS entries.
D. The names of the routers created using the hostname command.
E. The length of time of users logged into the router, as well as the duration
[单项选择]Which CLI command displays statistical information about a policy called goldservice ?（）
A. show ip interface atm 5/1.1
B. show policy-list goldservice
C. show profile name goldservice
D. show rate-limit-profile goldservice
[单项选择]Which configuration command dynamically detects and configures a PPPoA interface?（）
A. auto-configure ip
B. auto-configure ppp
C. auto-configure pppoe
D. auto-configure bridgedethernet
[单项选择]Which profile configuration command dynamically creates a host route in the routing table?（）
A. ip host routes
B. ip access-routes
C. host routes enabled
D. access-routes enabled
[单项选择]Which Cisco Catalyst feature automatically disables the port in an operational PortFast upon receipt of a BPDU?（）
A. BackboneFast
B. UplinkFast
C. Root Guard
D. BPDU Guard
E. BPDU Filter
[单项选择]Which command displays the current temperature of a Junos device's components?（）
A. show chassis temperature-thresholds
B. show chassis environment
C. show chassis hardware
D. show chassis alarms
[单项选择]Which command displays the egress interfaces selected on the PFE for destination prefixes?（）
A. show route forwarding-table
B. show route table
C. show route table extensive
D. show pfefwdd
[单项选择]Which command shows your active Telnet connections?（）
A. show session
B. show cdp neighbors
C. show users
D. show queue
[单项选择]Which Internet protocol encrypts and decrypts user page requests， as well as the pages that are returned by a web server using SSL？（）
A. NNTP
B. FTP
C. HTTP
D. HTTPS
[单项选择]The mksysb command completed successfully. Which of the following steps are necessary to verify the mksysb is good?（）
A. Store the mksysb in a safe place because a successful completion guarantees the mksysb is good.
B. Boot from the mksysb to verify it is bootable and list the files on the mksysb.
C. Look at the bosboot output when the mksysb was created to verify it is good.
D. List the files on the mksysb beucase listing all the files verifies there are no problems with the mksysb.
[单项选择]Which configuration command represents a static host route in a Routed 1483 network？（）
A. iproute 172.10.1.20.0.0.0 atm 6/0.33
B. iproute 172.10.1.2255.255.255.0 atm 6/0.33
C. iproute 172.10.1.2255.255.255.255 172.10.1.2
D. iproute 172.10.1.2255.255.255.255 atm 6/0.33
[单项选择]Which configuration command controls the source IP address for packets sent to a RADIUS server？（）
A. radius override nas-ip-addr
B. radius source-ip-address 10.13.7.55
C. radius update-source-address 10.13.7.11
D. radius authentication server 10.13.7.55
