更多"Which command would you configure g"的相关试题:
[单项选择]Which command would you configure globally on a Cisco router that would allow you to view directly connected Cisco devices?（）
A. enable cdp
B. cdp enable
C. cdp run
D. run cdp
[单项选择]At which command prompt would you issue the set date command?（）
A. [edit chassis] user@router#
B. [edit] user@router#
C. [edit system] user@router#
D. user@router>
[单项选择]Which IOS command would you enter if you wanted to view a list of IBGP and EBGP neighbor relationships that are configured（）
A. show ip bgp
B. show ip bgp paths
C. show ip bgp peers
D. show ip bgp summary
E. show ip bgp protocols
[单项选择]Which command would you use to view interface usage details in real time?（）
A. show interfaces terse
B. show interfaces extensive
C. monitor interface traffic
D. monitor traffic interface
[单项选择]Which command would you use to enable chassis cluster on an SRX device, setting the cluster ID to 1 and node to 0?（）
A. user@host# set chassis cluster cluster-id 1 node 0 reboot
B. user@host> set chassis cluster id 1 node 0 reboot
C. user@host> set chassis cluster cluster-id 1 node 0 reboot
D. user@host# set chassis cluster id 1 node 0 reboot
[单项选择]Which IOS command would you use to find out which networks are routed by a particular OSPF process（）
A. show ip ospf
B. show ip route
C. show ip protocols
D. show ip ospf database
E. None of the other alternatives apply
[单项选择]Which command would allow you to compare two files stored on your router?（）
A. user@host>file show filename1 compare filename2
B. user@host>file compare files filename1 filename2
C. user@host>compare files filename1 filename2
D. user@host>compare filename1 filename2
[单项选择]Which operational command would you use to quickly verify the state of all interfaces?（）
A. show interfaces terse
B. show interfaces
C. show configuration interfaces
D. show interface status
[单项选择]Which command would you type to see a concise display of which interfaces are up and which are down?（）
A. show interfaces brief
B. show interfaces status
C. show ip interface brief
D. show interfaces terse
[单项选择]Which command would allow you to login to FPC 1 to collect FPC specific logs?（）
A. start shell fpc1
B. start shell tnp1
C. start shell tnp address 1
D. start shell pfe network fpc1
[单项选择]Which would you NOT use to report the amount of anchor chain out? Three shots（）.
A. at the water's edge
B. on deck
C. on the bottom
D. well in the water
[单项选择]—Which would you like, a cup of tea or a glass of milk — ______ . I think I'll just have a glass of water.
[单项选择]Which would you like ______, basketball or football
[单项选择]What command would you use to view an IS-IS adjacency?（）
A. show iso neighbor
B. show isis neighbor
C. show iso adjacency
D. show isis adjacency
[单项选择]When troubleshooting ATM, which command would allow you to test reachability from one side of an ATM cloud to the other?（）
A. ping atm vci 0.100 interface at-0/1/0 end-to-end
B. ping atm vci 0.100 interface at-0/1/0 circuit
C. ping atm vci 0.100 interface at-0/1/0 far-end
D. ping atm vci 0.100 interface at-0/1/0 final-hop
[单项选择]Which command would correctly configure a serial port on a router with the last usable host address in the 192.216.32.32/29 subnet？（）
A. Router(config-if)# ip address 192.216.32.38 255.255.255.240
B. Router(config-if)# ip address 192.216.32.39 255.255.255.224
C. Router(config-if)# ip address 192.216.32.63 255.255.255.248
D. Router(config-if)# ip address 192.216.32.39 255.255.255.248
E. Router(config-if)# ip address 192.216.32.38 255.255.255.248
[单项选择]Which command would display OSPF parameters such as filters，default metric，maximum paths，and number of areas configured on a outer（）
A. show ip protocol
B. show ip route
C. show ip ospfinterface
D. show ip ospf
E. show ip nterface
F. None of the other alternatives apply
[多项选择]Which options would you consider while configuring a flash recovery area (fast recovery area in 11g Release 2) for your production database that is running in ARCHIVELOG mode?（）
A. Setting the FAST_START_MTTR_TARGET to set the mean time to recover
B. Setting the RECOVERY_PARALLELISM parameter to twice the number of CPUs
C. Using the DB_RECOVERY_FILE_DEST parameter to set the location for flash recovery area
D. Using the DB_RECOVERY_FILE_DEST_SIZE parameter to define the disk space limit for the recovery files created in the flash recovery area
