更多"Which of the commands below would y"的相关试题:
[多项选择]Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?（）
A. Switch(config-if)# vlan all
B. Switch(config-if)# switchport trunk encapsulation dot1q
C. Switch(config-if)# switchport access vlan all
D. Switch(config-if)# switchport mode trunk
E. Switch(config-if)# switchport access vlan 303
[多项选择]Which two commands would you use to discard a candidate configuration?（）
A. rollback
B. delete
C. delete 0
D. rollback 0
[多项选择]Which two commands would you use to view OSPF routes?（）
A. show ip route ospf
B. show ospf routes
C. show route protocol ospf
D. show route
[多项选择]Which of the commands below can you use to configure a default route?（）
A. TK1(config)# ip route 0.0.0.0 0.0.0.0 E0
B. TK1(config)# ip route 0.0.0.0 255.255.255.255 S0
C. TK1(config-interface)# ip route 255.255.255.255 0.0.0.0 192.168.1.21
D. TK1(config)# ip route 0.0.0.0 0.0.0.0 192.168.1.21
E. TK1(config)# ip route 0.0.0.0 192.168.1.21 255.255.255.255
F. TK1# ip default-network 0.0.0.0 192.168.1.21 255.255.255.255
[单项选择]Which one of the following commands would you enter to terminate a VTY line session?（）
A. close
B. disable
C. disconnect
D. suspend
E. exit
F. None of the above
[单项选择]Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?（）
A. Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0
B. Router(config)# ip route 0.0.0.0 255.255.255.255 s0
C. Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0
D. Router(config)# ip route 0.0.0.0 0.0.0.0 s0
E. Router(config)# ip route any any e0
[单项选择]Which of the following commands would successfully implement an access list on a routers virtual terminal line?（）
A. RouterTK(config-line)# access-class 10 in
B. RouterTK(config-if)# ip access-class 23 out
C. RouterTK(config-line)# access-list 150 in
D. RouterTK(config-if)# ip access-list 128 out
E. RouterTK(config-line)# access-group 15 out
F. RouterTK(config-if)# ip access-group 110 in
[多项选择]Which two commands would change the default OSPF metric calculation for interface ge-0/3/0 inJUNOS software?（）
A. set interfaces ge-0/3/0 unit 0 metric 10
B. set protocols ospf reference-bandwidth 10g
C. set interfaces ge-0/3/0 unit 0 bandwidth 10g
D. set protocols ospf area 0 interface ge-0/3/0 metric 10
E. set protocols ospf area 0 interface ge-0/3/0 bandwidth 10g
[单项选择]Which IOS command would you enter if you wanted to view a list of IBGP and EBGP neighbor relationships that are configured（）
A. show ip bgp
B. show ip bgp paths
C. show ip bgp peers
D. show ip bgp summary
E. show ip bgp protocols
[多项选择]Which three commands allow you to verify the current state of your BGP neighbors?（）
A. show bgp group
B. show bgp status
C. show bgp summary
D. show bgp neighbor
E. show protocols bgp
[单项选择]Which of the following commands would MOST likely be used to see where a loss of connectivity between two devices on a network is located?（）
A. tracert
B. netstat
C. nslookup
D. ping
[单项选择]Which of the following commands would a technician use to view the active applicationconnections on a local PC to the network?（）
A. ipconfig
B. netstat
C. nslookup
D. net use
[多项选择]Which two commands allow you to return to a previous verision of software on the device?（）
A. request sytem software add
B. request sytem software downgrade
C. request sytem software replace
D. request sytem software rollback
[单项选择]Which of the following commands would verify the health of the sectors on a hard drive andrecover data on damaged sectors?（）
A. TRACERT
B. SFC
C. CHKDSK
D. NSLOOKUP
