[单项选择]If you have Cisco integrated services router and need to upgrade the Cisco IOS image,which kind of Cisco Support services do you need?（）
A. Cisco SMARTNet onsite
B. Cisco TAC
C. Advanced Hardware Replacement
D. Software Support

[单项选择]Why is the Cisco Integrated Services Router product line A good choice for customers?（）
A. it isA point product solution that addresses a single need
B. it provides customers with an opportunity to increase the number of devices in their network
C. it simplifies purchasing because there is only one model to choose.
D. it integrates multiple services intoA single platform and reduces operating costs.

[单项选择]You have just obtained a modular Cisco router with 2 serial connections and a BRI/U interface. What other physical piece of hardware is required in order to establish an ISDN connection?（）
A. Nothing. The router is already suitable.
B. A BRI WAN interface in the router.
C. An external NT1 to terminate the local loop.
D. A TA/NT1 device on the router.

[多项选择]For which two reasons are Integrated Services Routers well-positioned for the SMB market?（）
A. They are integrated with firewall capabilities.
B. They scan packets for malicious activity.
C. They offer superior site-to-site routing.
D. They require no configuration to install.
E. They offer the best choice for remote access needs.

[单项选择]You are upgrading your Cisco router IOS from a TFTP server over the network. The upgrade procedure is stopped and you are prompted to erase the current flash contents before continuing. What is most plausible reason for this? （）
A. There is insufficient room for more than one image.
B. The router has detected a copy of the current software image on the TFTP server.
C. The file can be relocated and not compressed.
D. The image to load is a binary executable file.

[单项选择] OSPF is enabled on router A. You execute the following command on router A and receive theaccompanying output:RouterA#ping 224.0.0.5 repeat1Type escape sequence to abort.Sending 1, 1 00 - byte ICMP Echos to 224.0.0.5, timeout is 2 seconds:Reply to request 0 from 10.100.100.1, 4 ms10.100.100.1 is the IP address of a loopback interface on router A. What can you conclude about router A?（）
A. Only the router A loopback interface is parti cipating in the OSPF routing process
B. None of the router A interfaces are participating in the OSPF routing process
C. Router A is using the loopback interface IP address as its OSPF router ID
D. Router A does not have any reachable OSPF neighbors

[单项选择]You have a Level 1-only router (Router A) in IS-IS area 49.0001. How does Router A learn how to get to IP prefixes in other areas?（）
A. Router A must have a Level 2 adjacency with the Level 1/Level 2 router in area 49.0001.
B. The Level 1/Level 2 router in area 49.0001 sets the "attached" bit in the Level 1 link-state PDU (LSP) it floods into area 49.0001.
C. The Level 1/Level 2 router in area 49.0001 sets the "attached" bit in the Level 2 LSP it floods into area 49.0001.
D. The Level 1/Level 2 router in area 49.0001 advertises these prefixes into area 49.0001 using a Level 2 LSP it floods into the area.

[多项选择]You have been asked to configure your router to send link-related SNMP trap notifications to the network managemetn system (NMS) located at address 172.16.17.1.Which two commands are required?（）
A. set snmp trap-group my-trap-group targets 172.16.17.1
B. set snmp targets 172.16.17.1
C. set snmp trap-group my-trap-group link-status
D. set snmp trap-group my-trap-group categories link

[单项选择]You have just purchased a brand new router and wish to have the router prompt you through the initial configuration commands. Which router mode does this describe?（）
A. ROM Monitor mode
B. SETUP mode
C. Autoflash mode
D. RXBOOT mode
E. None of the above

[单项选择]You have just issued the command user@router# save current.conf.Assuming the default settings, where in the file system is current.conf saved?（）
A. /var/tmp/
B. /var/config/saved/
C. /var/home/user/
D. /config/

[多项选择]As a Cisco Network Engineer, you have to master the knowledge of the Cisco validated Design (CVD) program. Which three of the following descriptions are appropriate about the CVD program?（） (Choose three.)
A. It incorporates a narrow range of technologies and products.
B. It facilitates faster and more reliable customer deployments.
C. It extends the value of designs through a sustained development plan.
D. It incorporates products and technologies into enterprise, service provider, and commercial systems.

[多项选择]Which two of the following Cisco router platforms support Multicast Distributed Fast Switching?（）
A. 3600 series
B. 7200 series with NSE-1
C. 7500 series
D. 12000 series