[单选题]
A network administrator needs to configure a serial link between the main office and a remote location.The
Router at the remote office is a non-cisco router. How should the network administrator configure the serial
Interface of the main office router to make the connection?
A. Main(config)#interface serial 0./0.Main(config-if)#no shut
B. Main(config)#interface serial 0./0.Main(config-if)#encapsulation ietfMain(config-if)#no shut
C. Main(config)#interface serial 0./0.Main(config-if)#encapsulation frame-relayMain(config-if)#authenication chapMain(config-if)#no shut
D. Main(config)#interface serial 0./0.Main(config-if)#encapsulation pppMain(config-if)#no shut

[单选题]
A network administrator needs to allow only one Telnet connection to a router. For anyone viewing the
Confguration and issuing the show run command, the password for Telnet access should be encrypted.
Which set of commands will accomplish this task?
A. service password-encryptionline vty 0. 4.loginpassword ciscoaccess-class 1.
B. enable password secretline vty 0.loginpassword cisco
C. service password-encryptionline vty 1.loginpassword cisco
D. service password-encryptionline vty 0. 4.loginpassword cisco

[多选题]
An administrator would like to configure a switch over a virtual terminal connection from locations outside
Of the local LAN. Which of the following are required in order for the switch to be configured from a remote
Location? (Choose two.)
A. The switch must be configured with an IP address, subnet mask, and default gateway.
B. The switch must be connected to a router over a VLAN trunk.
C. The switch must be reachable through a port connected to its management VLAN.
D. The switch console port must be connected to the Ethernet LAN.
E. The switch management VLAN must be created and have a membership of at least one switch port.
F. The switch must be fully configured as an SNMP agent.

[单选题]29 An LTM Specialist needs to configure a virtual server with the requirements displayed below. Application is currently an internal HTTP application
Encrypted external user access
Links are hard for siteA example.com and need to rewritten to siteB.Example.com Which profiles must the LTM Specialist use to provide the proper functionality?
A.Clientssll, Stream
B.Serverless, Stream
C.Clientssl, fastL4, Stream
D.Serverless, fastL4, Stream

[单选题]5 An TLM Specialist needs to configure a virtual server to terminate SSL connection on the LTM device.
Cryptographic information must be re-authorized for SSL sessions that remain open for longer than 30 seconds.
Which settings should the LTM Specialist configure in the client SSL profile?
A.set the Handshake Timeout to 30 seconds
B.enable Require Peer SN1 Support
C.set the Renegotiate Period to 30 seconds
D.set the Renegotiate Max Record Delay to 30

[多选题]68 An LTM Specialist needs to configure a setup for antivirus scanning of HTTP traffic with an internet Contact adaption Protocol (ICAP) server.
Which two server type should be used? (Choose two.)
A.Standard
B.Internal
C.Performance HTTP
D.Forwarding IP
E.Stateless

[单选题]
The network administrator has discovered that the power supply has failed on a switch in the company LAN
And that the switch has stopped functioning. It has been replaced with a Cisco Catalyst 295.0. series switch.
What must be done to ensure that this new switch becomes the root bridge on the network?
A. Lower the bridge priority number.
B. Change the MAC address of the switch.
C. Increase the VTP revision number for the domain.
D. Lower the root path cost on the switch ports.
E. Assign the switch an IP address with the lowest value.

[单选题]
A network administrator is troubleshooing an EIGRP problem on a router and needs to confirm the IP
Addresses of the devices with which the router has established adjacency. The retransmit interval and the
Queue counts for the adjacent routers also need to be checked. What command will display the required
Information?
A. Router# show ip eigrp adjacency
B. Router# show ip eigrp topology
C. Router# show ip eigrp interfaces
D. Router# show ip eigrp neighbors

[单选题]
A network administrator is troubleshooting the OSPF configuration of routers R1. and R2.. The routers
Cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of
The show ip ospf interface e0. command for routers R1. and R2.. Based on the information in the graphic,
What is the cause of this problem?
A. The OSPF area is not configured properly.
B. The priority on R1. should be set higher.
C. The cost on R1. should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.

[单选题]
A network administrator is verifying the configuration of a newly installed host by establishing an FTP
Connection to a remote server. What is the highest layer of the protocol stack that the nework administrator
Is using for this operation?
A. application
B. presentation
C. session
D. transport
E. internet
F. data link

[多选题]A network administrator changes the configuration register to 0.x214.2. and reboots the router. What are tworesults of making this change? (Choose two.)
A. The IOS image will be ignored.
B. The router will prompt to enter initial configuration mode.
C. The router will boot to ROM.
D. Any configuration entries in NVRAM will be ignored.
E. The configuration in flash memory will be booted.

[单选题]
Which command helps a network administrator to manage memory by displaying flash memory andNVRAM utilization?
A. show secure
B. show file systems
C. show flash
D. show version

[单选题]
Refer to the exhibit. A network administrator attempts to ping Host2. from Host1. and receives the result that
Are shown. What is a possible problem?
A. The link between Host1. and Switch1. is down.
B. TCP/IP is not functioning on Host1..
C. The link between Router1. and Router2. is down.
D. The default gateway on Host1. is incorrect.
E. Interface Fa0./0. on Router1. is shudown.
F. The link between Switch1. and Router1. is down.

[多选题]
A network administrator wants to ensure that only the server can connect to port Fa0./1. on a Catalyst
Switch. The server is plugged into the switch Fa0./1. port and the network administrator is about to bring the
Server online. What can the administrator do to ensure that only the MAC address of the server is allowed
By switch port Fa0./1.? (Choose two.)
A. Configure port Fa0./1. to accept connections only from the static IP address of the server.
B. Employ a proprietary connector type on Fa0./1. that is incompatible with other host connectors.
C. Configure the MAC address of the server as a static entry associated with port Fa0./1..
D. Bind the IP address of the server to its MAC address on the switch to prevent other hosts from spoofingthe server IP address.
E. Configure port security on Fa0./1. to reject traffic with a source MAC address other than that of theserver.
F. Configure an access list on the switch to deny server traffic from entering any port other than Fa0./1..

[多选题]
What are two reasons a network administrator would use CDP? (Choose two.)
A. to verify the type of cable interconnecting two devices
B. to determine the status of network services on a remote device
C. to obtain VLAN information from directly connected switches
D. to verify Layer 2. connectivity between two devices when Layer 3. fails
E. to obtain the IP address of a connected device in order to telnet to the device
F. to determine the status of the routing protocols between directly connected routers

[多选题]A network administrator is explaining VTP configuration to a new technician. What should the network
Administrator tell the new technician about VTP configuration? (Choose three.)
A. A switch in the VTP client mode cannot update its local VLAN database.
B. A trunk link must be configured between the switches to forward VTP updates.
C. A switch in the VTP server mode can update a switch in the VTP transparent mode.
D. A switch in the VTP transparent mode will forward updates that it receives to other switches.
E. A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTPrevision number.
F. A switch in the VTP server mode will update switches in the VTP client mode regardless of the
Configured VTP domain membership.

[单选题]
Refer to the exhibit,a network administrator cannot establish a telnet session with the indicated router.Whatis the cause of this failure?
A. A level 5. password is not set
B. The vty password is missing
C. The console password is missing
D. An ACL is blocking Telnet access