更多"The amount of fluid delivered by a "的相关试题:
[单项选择]The amount of fluid delivered by a screw pump can be regulated by （）.
A. throttling the pressure line
B. changing the speed of the rotor
C. either A or B
D. None of the above is tree
[单项选择]The amount of fluid delivered by a helical pump can be regulated by （）.
A. throttling the pressure line
B. changing the speed of the rotor
C. either A or B
D. None of the above is tree
[单项选择]The amount of fluid delivered by a positive displacement pump can be regulated by （）.
A. throttling the pressure line
B. changing the speed of the driving rotor
C. either A or B
D. None of the above is tree
[单项选择]The amount of fluid delivered by a reciprocating pump can be regulated by （）.
A. throttling the pressure line
B. changing the speed of the piston
C. either A or B
D. None of the above is tree
[单项选择]The amount of fluid delivered by a centrifugal pump can be regulated by （）.
A. throttling the pressure line
B. changing the speed of the rotor
C. either A or B
D. None of the above is tree
[单项选择]The control rod of a steering gear pump is attached at its outer end to （）.
A. the hunting gear
B. the rudder stock
C. the rudder controller
D. the feedback unit
[单项选择]A spur gear pump should be operated with the discharge valves （）.
A. slightly opened
B. throttled
C. fully opened
D. halfway opened
[单项选择]An advantage of a helical gear pump over a simple gear pump is that the helical gear pump is capable of （）.
A. maintaining a steadier speed
B. delivering liquids over greater distances
C. operating for longer periods of time
D. producing a smoother discharge flow
[单项选择]A gear pump belongs to （） according to its working principle.
A. reciprocating pumps
B. positive displacement pumps
C. centrifugal pumps
D. centripetal pumps
[单项选择]A multistage centrifugal pump can be BEST described as having （）.
A. two or more impellers housed together in one casing and mounted on a single shaft
B. a single stepped impeller mounted in a progressively staged casing
C. a large radial clearance between the impeller and casing to prevent overheating due to
D. an increase in the discharge velocity of the liquid with a corresponding decrease in pressure through the stages
[单项选择]The capacity of a centrifugal pump can be increased by the installation of a larger diameter impeller Another means of increasing the pump capacity is to （）.
A. increase speed
B. increase the size of the cardent assembly
C. reduce wearing ring clearances
D. change the pump to a "close coupled" arrangement
[单项选择]A water pump can not supply water after startingIt may be caused by （）.
A. closed discharge valve
B. broken pipe line
C. worn shaft
D. both A and B
[单项选择]Shaft sealing in a centrifugal pump can be effected by （）.
A. the mechanical seal
B. packed stuffing boxes
C. either A or B
D. neither A nor B
[单项选择]A centrifugal pump can’t supply water after startingYou should check （）.
A. priming water
B. power supply
C. packing gland
D. bearing lubrication
[单项选择]The reciprocating pump can’t draw water from a tank may be caused by （）.
A. leaky pipe
B. opened inlet valve
C. too much water in tank
D. None of the above
[单项选择]The pressure of a liquid leaving the pump can be referred to as the （）.
A. total head
B. discharge head
C. net positive suction head
D. suction head
[单项选择]The amount of fuel delivered by a helical plunger fuel injection pump is controlled by （）
A. varying the pump discharge pressure
B. varying the pump return pressure
C. rotation of the pump plunger
D. rotation of the pump barrel
[单项选择]The amount of fuel delivered by a unit injector is controlled by the （）
A. camshaft
B. main spring
C. rack position
D. nozzle orifice size
[单项选择]The amount of fuel delivered for each cycle must be in accordance with the engine load, and the same quantity of fuel must be delivered to each cylinder for each power stroke at that load.Which of the following statements describes this requirement?（）
A. Proper timing
B. Accurate metering
C. Suitable injection rate
D. Suitable atomization rate
