更多"You issued the following commands t"的相关试题:
[多项选择]Which three commands allow you to verify the current state of your BGP neighbors?()
A. show bgp group
B. show bgp status
C. show bgp summary
D. show bgp neighbor
E. show protocols bgp
[单项选择]Which one of the following commands would you enter to terminate a VTY line session?()
A. close
B. disable
C. disconnect
D. suspend
E. exit
F. None of the above
[多项选择]Which of the following IOS commands could you use to troubleshoot a router connectivity problem on an IP network?()
A. show ip route
B. ipconfig
C. tracert
D. show interfaces
E. traceroute
F. ping
G. All of the above
[多项选择]Which interface commands would you enter on a Catalyst 2900 switch, if your goal was to bring all VLAN traffic to another directly connected switch?()
A. Switch(config-if)# vlan all
B. Switch(config-if)# switchport trunk encapsulation dot1q
C. Switch(config-if)# switchport access vlan all
D. Switch(config-if)# switchport mode trunk
E. Switch(config-if)# switchport access vlan 303
[多项选择]Which two commands allow you to return to a previous verision of software on the device?()
A. request sytem software add
B. request sytem software downgrade
C. request sytem software replace
D. request sytem software rollback
[多项选择]Which two commands would you use to discard a candidate configuration?()
A. rollback
B. delete
C. delete 0
D. rollback 0
[多项选择]Which two commands would you use to view OSPF routes?()
A. show ip route ospf
B. show ospf routes
C. show route protocol ospf
D. show route
[单项选择]Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?()
A. Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0
B. Router(config)# ip route 0.0.0.0 255.255.255.255 s0
C. Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0
D. Router(config)# ip route 0.0.0.0 0.0.0.0 s0
E. Router(config)# ip route any any e0
[单项选择]Which of these commands can you use to show if an operational Catalyst switch port is set for autonegotiation of speed and duplex when running Cisco IOS software?()
A. show port network
B. show running-config
C. show controllers Ethernet-controller
D. show interfaces
[单项选择]Which of the commands below would you enter if you wanted to see the configuration register of your router?()
A. show boot
B. show flash
C. show register
D. show version
E. show config
[多项选择]Which two initialization parameters would you set to enable Automatic Shared Memory Management?()
A. set SHARED_POOL_SIZE to zero
B. set STATISTICS_LEVEL to BASIC
C. set SGA_TARGET to a non-zero value
D. set DB_CACHE_SIZE to a non-zero value
E. set STATISTICS_LEVEL to TYPICAL or ALL
[单项选择]If IP routing is enabled, which two commands set the gateway of last resort to the default gateway? ()
A. ip default-gateway 0.0.0.0
B. ip route 172.16.2.1 0.0.0.0 0.0.0.0
C. ip default-network 0.0.0.0
D. ip default-route 0.0.0.0 0.0.0.0 172.16.2.1
E. ip route 0.0.0.0 0.0.0.0 172.16.2.1
[单项选择]Which set of configuration commands configures MBGP on the ERX Edge Router?()
A. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 multicast neighbor 192.168.10.1 next-hop-self
B. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family vpnv4 multicast neighbor 192.168.10.1 activate
C. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 unicast neighbor 192.168.10.1 active
D. router bgp 100 neighbor 192.168.10.1 remote-as 200 address-family ipv4 multicast neighbor 192.168.10.1 activate