更多"Which of the following commands sho"的相关试题:
[单项选择]Which of the following ping commands would a technician use to ping continuously?（）
A. PING -l
B. PING -R
C. PING -t
D. PING -a
[多项选择]Which of the following IOS commands could you use to troubleshoot a router connectivity problem on an IP network?（）
A. show ip route
B. ipconfig
C. tracert
D. show interfaces
E. traceroute
F. ping
G. All of the above
[单项选择]Which one of the following EIGRP commands can check the IP addresses of the adjacent neighbors, as well as verifying the EIGRP retransmit intervals and queue counts?（）
A. TK1#show ip eigrp adjacency
B. TK1#show ip eigrp topology
C. TK1#show ip eigrp interfaces
D. TK1#show ip eigrp neighbors
E. None of the above
[多项选择]Which of the following OSPF commands, when used together, will put the network 192.168.10.0/24 into OSPF area 0?（）
A. Router(config-router)# network 192.168.10.0 0.0.0.255 0
B. Router(config-router)# network 192.168.10.0 0.0.0.255 area 0
C. Router(config-router)# network 192.168.10.0 255.255.255.0 area 0
D. Router(config)# router ospf 0
E. Router(config)# router ospf 1
[单项选择] The following configuration commands exist only in an implementation plan document. An engineer does a copy/paste of these commands into configuration mode on Router R1. Which of the following answers is m ost accurate regarding the results?（） ip sla 1 icmp - echo 1.1.1.1 source -ip 2.2.2.2 ip sla schedule 1 start - time now life forever
A. The SLA operation will be configured but will not start until additional commands are used
B. The SLA operation is not comp letely configured so it will not collect any datA
C. The SLA operation is complete and working, collecting data into the RTTMON MIB
D. The SLA operation is complete and working but will not store the data in the RTTMON MIB without more configuration
[多项选择]Which of the following commands verifies connectivity between two hosts?（）
A. chkntfs
B. dxdiag
C. tracert
D. ipconfig
E. ping
[单项选择]Which of the following commands would successfully implement an access list on a routers virtual terminal line?（）
A. RouterTK(config-line)# access-class 10 in
B. RouterTK(config-if)# ip access-class 23 out
C. RouterTK(config-line)# access-list 150 in
D. RouterTK(config-if)# ip access-list 128 out
E. RouterTK(config-line)# access-group 15 out
F. RouterTK(config-if)# ip access-group 110 in
[多项选择]Which of the following commands provides similar information about the current configuration ofactive local Ethernet adapters? (Select TWO)（）
A. traceroute
B. ipconfig
C. ifconfig
D. route
E. hostname
[单项选择]Which of the following commands would MOST likely be used to see where a loss of connectivity between two devices on a network is located?（）
A. tracert
B. netstat
C. nslookup
D. ping
[单项选择]Which of the following commands will list available paging space on a system?（）
A. lsps
B. lsps -a
C. lsps -pg
D. lsps ALL
[单项选择]Which of the following commands scans and verifies system protected files?（）
A. VERIFY
B. SFC
C. CHKDSK
D. CHKNTFS
[单项选择]Which of the following commands will display what space is used in /tmp filesystem?（）
A. df -Ik /tmp
B. df -fk /tmp
C. df -Uk /tmp
D. df -Fk /tmp
[单项选择]Which of the following commands would a technician use to view the active applicationconnections on a local PC to the network?（）
A. ipconfig
B. netstat
C. nslookup
D. net use
[单项选择]Which of the following commands will allow remote use of a folder?（）
A. NET SEND
B. NET SHARE
C. NET FILE
D. NET VIEW
[单项选择]Which of the following sequence of commands should be used to list the directories and files saved on a mksyst tape that has been rewound and placed in device rmt0?（）
A. tet1 -f /dev/rmt0 fsf 2; restore -xqvf /dev/rmt0
B. tet1 -f /dev/rmt0.1 fsf2; restore -Tvf /dev/rmt0.1
C. tet1 -f /dev/rmt0.1 fsf3; restore Tqvf /dev/rmt0.1
D. tet1 -f /dev/rmt0.1 fsf3; restore -Tvf /dev/rmt0.1
[单项选择]Which of the following sequence of commands extracts the third image from a tape that was created using the backup command?（）
A. tctl -f /dev/rmt0.1 fsf 2 ; tar -xv file3
B. tctl -f /dev/rmt0.0 fsf 3 ; dd if=file3 pf =/dev/mt0.1
C. tctl -f /dev/rmt0.1 fsf 2 ; dd if=/dev/rmt0.1 of=file3
D. tctl -f /dev/rmt0.0 fsf 3 ; dd if=/dev/rmt0.1 of=file3
[单项选择]Which of the following ALTER DISKGROUP commands does not use V$ASM_OPERATION to record thestatus of the operation?（）
A. ADD DIRECTORY
B. DROP DISK
C. RESIZE DISK
D. REBALANCE
E. ADD FAILGROUP
