更多"Which method loads the configuratio"的相关试题:
[单项选择]Given the following LSP configuration, which statement is true?（）label-switched-path lsp-xyz { to 10.200.1.1; primary path1; secondary path2; secondary path3; no-cspf; } path path1 { 10.200.10.1 strict; } path path2 { 10.200.20.1 strict; } path path3 { 10.200.30.1 loose; }
A. The router will use path1 when it is available and stable.
B. The router will use path3 when it is available and stable.
C. The router will attempt to establish path2 only when path1 and path3 are down.
D. The router will attempt to establish path1 only when path2 and path3 are down.
[单项选择]Assuming the default switch configuration,which approach should you use to configure the extended vlan range(1006 through 4094) on a cisco catalyst 3750 series switch?（）
A. Configure the switch to be in VTP client mode.
B. Configure the switch to be in VTP domaint mode.
C. Configure the switch to be in VTP transparent mode.
D. Configure the switch to be in VTPv2.
[单项选择]What is one configuration method for loading a factory default configuration onto a J-series router？（）
A. load override reset
B. load factory-default
C. rollback factory-default
D. request system factory-default
[单项选择]assuming the default switch configuration which vlan range can be added modified and removed on a cisco switch?（）
A. 2 through 1001
B. 1 through 1001
C. 1 through 1002
D. 2 through 1005
[多项选择]Firewall filter policers can perform which two actions?（）
A. Set the next hop.
B. Discard packets.
C. Set loss priority.
D. Sample packet content.
[单项选择]Which configuration command configures queue buffer allocation on the ERX Edge Router?（）
A. qos-profile
B. queue-profile
C. scheduler-profile
D. traffic-shape-profile
[单项选择]Which configuration shows the correct application of a security policy scheduler?（）
A. [edit security policies from-zone Private to-zone External] user@host# show policy allowTransit { match { source-address PrivateHosts; destination-address ExtServers; application ExtApps; } then { permit { tunnel { ipsec-vpn myTunnel; } scheduler-name now; } } }
B. [edit security policies from-zone Private to-zone External] user@host# show policy allowTransit { match { source-address PrivateHosts; destination-address ExtServers; application ExtApps; } then { permit { tunnel { ipsec-vpn myTunnel; } } } scheduler-name now; }
C. [edit security policies from-zone Private to-zone External] user@host# show policy allowTransit { match { source-address PrivateHosts; destination-address ExtServers; application ExtApps; } then { permit { tunnel { ipsec-vpn scheduler-name now; } } } }
D. [edit security policies from-zone Private to-zone External] user@host# show policy allowTransit { match { source-address PrivateHosts; destination-address ExtServers; application ExtApps; scheduler-name now; } then { permit { tunnel { ipsec-vpn myTunnel; } } } scheduler-name now; }myTunnel;
[单项选择]Which configuration command permits dynamic detection of the ATM frame format?（）
A. aal5mux
B. aal5snap
C. aal5dynamic
D. aal5autoconfig
[单项选择]Which configuration command dynamically detects and configures a PPPoA interface?（）
A. auto-configure ip
B. auto-configure ppp
C. auto-configure pppoe
D. auto-configure bridgedethernet
[单项选择]Which profile configuration command dynamically creates a host route in the routing table?（）
A. ip host routes
B. ip access-routes
C. host routes enabled
D. access-routes enabled
[单项选择]Which configuration command creates a virtual router called isp-1？（）
A. virtual-routerisp-1
B. virtual-routerISP-1
C. virtual-routerVRisp-1
D. virtual-routerVRISP-1
[单项选择]Which configuration command sets the MPLS interface bandwidth to 15 Mbps?（）
A. set bandwidth 15
B. mpls bandwidth 15
C. set bandwidth 15000
D. mpls bandwidth 15000
[单项选择]Which configuration command represents a static host route in a Routed 1483 network？（）
A. iproute 172.10.1.20.0.0.0 atm 6/0.33
B. iproute 172.10.1.2255.255.255.0 atm 6/0.33
C. iproute 172.10.1.2255.255.255.255 172.10.1.2
D. iproute 172.10.1.2255.255.255.255 atm 6/0.33
[单项选择]Which configuration command controls the source IP address for packets sent to a RADIUS server？（）
A. radius override nas-ip-addr
B. radius source-ip-address 10.13.7.55
C. radius update-source-address 10.13.7.11
D. radius authentication server 10.13.7.55
[单项选择]Which configuration command represents a static customer route in a Routed 1483 network?（）
A. ip route 40.40.0.0255.255.0.0 172.10.1.2
B. ip route 40.40.0.00.0.255.255 atm 6/0.33
C. ip route 40.40.0.00.0.255.255 172.10.1.2
D. ip route 40.40.0.0255.255.0.0 atm 6/0.33
