更多"A network administrator needs to ad"的相关试题:
[单项选择]A network administrator needs to verify that switch interface 0/5 has been assigned to the Sales VLA.N. Which command will accomplish this task?()
A. Show vlan
B. Show mac-address-table
C. Show vtp status
D. show spanning-tree root
E. show ip interface brief
[单项选择]A network administrator needs to configure a router for a Frame Relay connection to a non-Cisco router. Which of the following commands will prepare the WAN interface for this connection?()
A. Router(config-if)# encapsulation frame-relay q933a
B. Router(config-if)# encapsulation frame-relay ansi
C. Router(config-if)# encapsulation frame-relay ietf
D. Router(config-if)# encapsulation frame-relay isl
E. None of the above
[单项选择]The network administrator needs to address seven LANs. RIP version 1 is the only routing protocol in use on the network and subnet 0 is not being used. What is the maximum number of usable IP addresses that can be supported on each LAN if the organization is using one class C address block?()
A. 8
B. 6
C. 30
D. 32
E. 14
F. 16
[单项选择]A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?()
A. Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#no shut
B. Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ietf Main(config-if)#no shut
C. Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation frame-relay Main(config-if)#authenication chap Main(config-if)#no shut
D. Main(config)#interface serial 0/0 Main(config-if)#ip address 172.16.1.1 255.255.255.252 Main(config-if)#encapsulation ppp Main(config-if)#no shut
[多项选择]A network administrator needs to configure port security on a switch.which two statements are true?()
A. The network administrator can apply port security to dynamic access ports
B. The network administrator can configure static secure or sticky secure mac addresses in the voice vlan.
C. The sticky learning feature allows the addition of dynamically learned addresses to the running configuration.
D. The network administrator can apply port security to EtherChannels.
E. When dynamic mac address learning is enabled on an interface,the switch can learn new addresses,up to the maximum defined.
[单项选择] An administrator needs to terminate network cables that have just been installed in the main communications closet. Which of the following tools is required?()
A. Multimeter
B. Snips
C. Toner probe
D. Punch down tool
[单项选择]An administrator needs to add fault tolerance capabilities to a server. Which of the following is the BEST solution to accomplish this?()
A. Move the architecture from 32-bit to 64-bit.
B. Install a PBX card.
C. Install a second NIC card.
D. Install a fail-over cable.
[单项选择]A network administrator needs to force a high-performance switch that is located in the MDF to become the root bridge for a redundant path switched network. What can be done to ensure that this switch assumes the role as root bridge()。
A. Establish a direct link from the switch to all other switches in the network.
B. Assign the switch a higher MAC address than the other switches in the network have.
C. Configure the switch so that it has a lower priority than other switches in the network.
D. Configure the switch for full-duplex operation and configure the other switches for half-duplex operation.
E. Connect the switch directly to the MDF router, which will force the switch to assume the role of root bridge.
[单项选择] A network administrator is trying to add a new router into an established OSPF network.The networks attached to the new router do not appear in the routing tables of the other OSPF routers.Given the information in the partial configuration shown below,what configuration error is causing this problem?() Router(config)#router ospf 1 Router(config-router)#network 10.0.0.0 255.0.0.0 area 0
A. The process id is configured improperly
B. The OSPF area is configured improperly
C. The network wildcard mask is configured improperly
D. The network number is configured improperly
E. The AS is configured improperly
F. The network subnet mask is configuerd improperly
[多项选择]The network administrator of the Oregon router adds the following command to the router configuration: ip route 192.168.12.0 255.255.255.0 172.16.12.1. What are the results of adding this command (Choose two.)()。
A. The command establishes a static route.
B. The command invokes a dynamic routing protocol for 192.168.12.0.
C. Traffic for network 192.168.12.0 is forwarded to 172.16.12.1.
D. Traffic for all networks is forwarded to 172.16.12.1.
E. This route is automatically propagated throughout the entire network.
F. Trafficfor network 172.16.12.0 is forwarded to the 192.168.12.0 network.
[单项选择]A network administrator wants to add a line to an access list that will block only Telnet access by the hosts on subnet 192.168.1.128/28 to the server at 192.168.1.5. What command should be issued to accomplish this task?()
A. access-list 101 deny tcp 192.168.1.128 0.0.0.15 192.168.1.5 0.0.0.0 eq 23 access-list 101 permit ip any any
B. access-list 101 deny tcp 192.168.1.128 0.0.0.240 192.168.1.5 0.0.0.0 eq 23 access-list 101 permit ip any any
C. access-list 1 deny tcp 192.168.1.128 0.0.0.255 192.168.1.5 0.0.0.0 eq 21 access-list 1 permit ip any any
D. access-list 1 deny tcp 192.168.1.128 0.0.0.15 host 192.168.1.5 eq 23 access-list 1 permit ip any any
[单项选择] A technician needs to add network capacity. However, when plugging a second switch into the first switch, there is no link light. Which of the following is the cause of this situation?()
A. The switches are not stackable
B. The cable was not wired using 568A
C. The cable needs to be a crossover cable
D. The switches have IGMP snooping enabled